Two Tone Government Build - 1911Forum
1911Forum
Advertise Here
Forum   Reviews   Rules   Legal   Site Supporters & Donations   Advertise


Go Back   1911Forum > >

Notices


Reply
 
Thread Tools Display Modes
  #1  
Old 01-16-2018, 07:51 PM
DesmoAndrew DesmoAndrew is offline
Member
 
Join Date: Jan 2015
Posts: 438
Two Tone Government Build

This pistol is the big brother to the two tone Commander I posted here last year. A Caspian slide on top of an 80% frame. I gotta say, these Caspian slides come in clean and the dimensions are what they should be. Makes the build much easier.

Pretty much a similar build spec and intent. Fairly plane pistol with a few touches that I wanted over a basic mil-spec pistol. Two-tone. Better sights. Ambi safety.

As with the previous build, David Clevinger did the blueing work. Really nice work and a nice smith to deal with. (he does engraving and I have a Series 70 repro that would look great with a little TLC from him sometime).

I've run about 800 rounds thru this one so far. Had to do a little work on the barrel throat to ease the sharp transition edge to get rid of the odd jam I had. (at first this pistol would feed fine with Chip McCormick power mags but not Colt OEM 7 rounders, now it takes all comers). I still ned to crown the barrel, and am waiting for a tool to do it. But good enough for 50 ft range work at present.

I'm running a EGW tool steel sear and ball disconnector and a Harrison retro hammer. They have come together to produce a very nice trigger pull and break.

The only thing I wish came out better is the EGW ambi safety. As best I can tell, there is a slight angular mis-match between the positioning of the LH and RH paddles that is do to the relative alignment of the fork and tongue shaft interface. The result is that the RH paddle ride just a tad high. Plan to call them to discuss. For all I know, it's my fitment that caused this. I also trimmed the shelfs a little more on this pistol. Will likely trim them more to get closer to the profile of the Wilson slim ambi safety.

The next project has just dropped out of the sky on me. A buddy “helpfully” pointed out that someone was selling bald 1911 slides on ebay for a song. So I got one to have it on hand. And then Cabella's listed Trijicon RMR type 1s for 349. So, just need a Caspian frame and more time.


-
-

-
-

-
-

-
-
Reply With Quote
  #2  
Old 01-27-2018, 07:09 PM
Ed_Gordon Ed_Gordon is offline
Member
 
Join Date: Apr 2014
Location: Central Illinois
Posts: 908
Looks great. Like said in your Commander thread - the two tone with blue up top on slide looks great. You can take very good pictures too!
__________________
Springfield Armory Milspec, RO compact & 1911 Loaded, Remington R1, Dan Wesson Heritage, Sig 1911 40 S&W, Ruger LW CMD, Colt LW Commander & Competition Series Government, CZ 1911 A1
Reply With Quote
  #3  
Old 01-27-2018, 07:44 PM
wproct wproct is offline
Member
 
Join Date: Nov 2008
Posts: 491
Quote:
Originally Posted by Ed_Gordon View Post
Looks great. Like said in your Commander thread - the two tone with blue up top on slide looks great. You can take very good pictures too!
Well said. The two tone and nice checkered wood grips works. Very attractive pistol!
Reply With Quote
Sponsored Links
Advertisement
 
  #4  
Old 02-18-2018, 01:03 PM
CyberDyneSystems CyberDyneSystems is offline
Member
 
Join Date: May 2017
Location: Providence
Posts: 1,012
Superb!
Reply With Quote
  #5  
Old 03-07-2018, 08:45 PM
samuse samuse is offline
Senior Member
 
Join Date: Oct 2008
Location: South Texas
Posts: 4,948
Gorgeous!
Reply With Quote
  #6  
Old 04-05-2018, 03:14 PM
dclevinger dclevinger is offline
Member
 
Join Date: Jun 2007
Location: Colorado
Posts: 248
Just came across your posts. The guns came out great! Fantastic work on the builds!
__________________
David Clevinger
Clevinger Customs
Reply With Quote
  #7  
Old 04-05-2018, 03:50 PM
RickB's Avatar
RickB RickB is offline
1911 Aficionado
 
Join Date: Mar 2000
Location: Not Seattle, WA, USA
Posts: 21,568
If you shorten the hammer spur, you can go with a M1911 grip safety for a higher grip and no bite from either the safety or the hammer.
It also addresses a high grip not disengaging the grip safety, as the hand is mostly in contact with the fixed part of the frame tangs.
__________________
If you're not shooting you should be moving. If you're not moving you should be reloading. If you're not shooting, moving, or reloading, you should be taping or picking brass. - Z.C.
Reply With Quote
  #8  
Old 04-11-2018, 03:11 PM
valor1 valor1 is offline
Member
 
Join Date: Oct 2003
Location: U.S. of A.
Posts: 273
Such a beauty!
__________________
STI Edge, STI Tactical, Glock 26, Cz-75,
Norinco, Glock 17, CZ P01, HK VP9 and still searching and still shooting
Reply With Quote
  #9  
Old 04-11-2018, 06:46 PM
JDpinardi JDpinardi is offline
Junior Member
 
Join Date: Mar 2018
Posts: 7
Meat and potatos, I love it!!!
JD
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:26 AM.


NOTICE TO USERS OF THIS SITE: By continuing to use this site, you certify that you have read and agree to abide by the Legal Terms of Use. All information, data, text or other materials ("Content") posted to this site by any users are the sole responsibility of those users. 1911Forum does not guarantee the accuracy, integrity, or quality of such Content.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2015 1911Forum.com, LLC. All Rights Reserved