taurus vs other 1911 grips? - 1911Forum
1911Forum
Advertise Here
Forum   Reviews   Rules   Legal   Site Supporters & Donations   Advertise


Go Back   1911Forum > >

Notices


Reply
 
Thread Tools Display Modes
  #1  
Old 09-21-2015, 06:54 PM
canrunin canrunin is offline
Member
 
Join Date: Dec 2011
Location: north east ohio
Posts: 85
taurus vs other 1911 grips?

so what is the difference between the taurus 1911 and all the other frames ? i keep seeing people saying you have to find grips that are for taurus for them to fit right? could some one show pictures or at least explain this? thank you
Reply With Quote
  #2  
Old 09-22-2015, 07:43 AM
PD5523 PD5523 is offline
Member
 
Join Date: Mar 2013
Posts: 365
The grip bushings are slightly larger- at least on the examples I've seen. Replace the grip bushings with standard bushings (the few I've done are not staked but may be loc-tited) and you are good to go!!
Reply With Quote
  #3  
Old 10-04-2015, 03:14 PM
StriderTacticaL StriderTacticaL is offline
Member
 
Join Date: May 2011
Location: CA
Posts: 376
I haven't noticed my aftermarket grips not fitting my 1911AR, but according to the VZ website, they make Taurus-specific 1911 grips due to the leg of the ambi-safety being a different length or something...
Reply With Quote
 
  #4  
Old 10-05-2015, 04:07 AM
Burgs Burgs is offline
Senior Member
 
Join Date: Feb 2010
Posts: 9,226
I used standard 1911 grips on my Taurus for years and never noticed a difference.

Taurus-specific grips are slightly wider, because the Taurus grip frame is slightly wider, fore and aft, than other 1911 grip frames.

RAASCO makes Taurus-specific grips, and last time I checked, they had an illustration explaining why their Taurus-specific grips were different than the usual 1911 grips.

Another source for excellent Taurus-specific custom crips is our forum member, Sarge, who is a custom grip maker of the first order and who is savvy in the ways of Taurus grips.

Sarge made these excellent custom smooth stag grips for my PT1911:
Attached Thumbnails
photo (25).JPG   photo (24).JPG  
__________________
Cordially, ~Burgs


"I've been up early my whole life, and all that ever did was increase the amount of time during the day something could go wrong." ~ Inspector O

Last edited by Burgs; 10-05-2015 at 04:15 AM.
Reply With Quote
  #5  
Old 11-08-2015, 12:11 AM
16-1911s 16-1911s is offline
Junior Member
 
Join Date: Nov 2015
Posts: 35
xxxxxxxxxx

Just today I got some Universal Springfield ,Kimber and others fs Houge black rubber wrap around grips w/finger groves. Went on my fs Tauri 1911 without any problem....
Attached Thumbnails
CAM00043.jpg  
Reply With Quote
  #6  
Old 11-08-2015, 05:33 PM
PD5523 PD5523 is offline
Member
 
Join Date: Mar 2013
Posts: 365
It appears Taurus may have begun using standard bushings after the first production runs given the experience of some others here.
Reply With Quote
  #7  
Old 11-09-2015, 07:01 AM
silversport silversport is offline
Member
 
Join Date: May 2003
Location: ChicagoLand***USA
Age: 55
Posts: 1,507
some stocks fit mine (PT1911AL) and some do not...mostly, I get binding on the ambit-safety other that looks...

Bill
__________________
**GSR Revolution STX**Custom II**Government XSE**Seecamp DA45**Government Super .38ACP**Taurus PT1911AL**
*NRA Benefactor/LEAA Life Member*Like What You've Got?...Thank a Vet*
"Fast is fine but accuracy is FINAL!"
Reply With Quote
  #8  
Old 11-17-2015, 02:25 AM
bubba1228 bubba1228 is offline
Junior Member
 
Join Date: Nov 2008
Location: Pueblo, CO
Age: 34
Posts: 18
+1 on Raasco Grips. Good site, good stuff.
Reply With Quote
  #9  
Old 02-04-2016, 11:30 PM
HotToyz HotToyz is offline
Member
 
Join Date: Mar 2006
Posts: 195
Pt 1911 Grips

Mine was manufactured in May of 2015. All my 1911 grips fit perfectly. But, the ambidextrous side is a little different. There is more of a slope of the angle of the ones made for the PT 1911. A VERY easy modification! A dremil and three minutes.

Just compare your factory grips. To any standard ambidextrous grip. And if you look at the Raasco site, you'll see the angle everyone is talking about. You can also go to the VZ site and look under FAQ and click on the link under Taurus/STI and there is a great diagram showing the angle!

But you can use most ANY 1911 grip set,with a tiny mod! Very easy fix!
__________________
Own A Colt Or Own A Copy!
Reply With Quote
  #10  
Old 02-08-2016, 05:31 PM
1saxman 1saxman is offline
Senior Member
 
Join Date: Jun 2003
Posts: 13,241
The grips are standard except the Taurus grip screw heads are a little wider so you have to use standard screws with standard grips. Here are generic Cocobolo grips on my Taurus with Allen key screws.

Reply With Quote
  #11  
Old 03-17-2016, 08:44 PM
Mpanova Mpanova is offline
Member
 
Join Date: Mar 2011
Location: Houston Texas
Age: 39
Posts: 59
The bushings on the Taurus frame sit back toward the rear of the gun about 1/16th-1/8th inch leaving more frame showing if you use standard grips, check out the examples on raasco grips website
Reply With Quote
  #12  
Old 04-19-2017, 12:22 AM
dieseltech dieseltech is offline
Junior Member
 
Join Date: Apr 2017
Location: MN
Posts: 22
I got my grips from rio grande they fit perfectly on my PT1911B except the screws must be replaced with standard 1911 screws I chose Wilson allen heads.

The only difference I've noticed aside from the screws is the ambi safety cut my Taurus is the only 1911 I have or have had with a ambi safety.

I still can't figure out how to upload pics so I can show it off.
__________________
Master Mechanic

USMC Vet
Reply With Quote
  #13  
Old 05-04-2017, 01:27 PM
1saxman 1saxman is offline
Senior Member
 
Join Date: Jun 2003
Posts: 13,241
Quote:
Originally Posted by Mpanova View Post
The bushings on the Taurus frame sit back toward the rear of the gun about 1/16th-1/8th inch leaving more frame showing if you use standard grips, check out the examples on raasco grips website
This is not the case. If it were, the grip might cover the mainspring housing pin. My picture is a little fuzzy but looking at the pistol just now I can see that the relief is centered around the pin as it should be. Rather, Taurus for some reason does not wrap the curvature of the front strap around like the Colt/mil-standard, so a little more flat appears on the front side of the grips. It really is a very minor thing (I don't have large hands and I don't notice it) so don't hold back on the grips you want - they'll fit. You'll just need standard size screw heads to go with standard grips. Why do they use larger diameter screw heads? The same reason Colt does on the M45A1; a larger screw head exerts more force on the grip to resist shooting loose. Seems logical but I haven't really tested it. Here's a better view. Also, if the grip were shifted back which would be the result of shifted bushings, the grip would interfere with the thumb safety.

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:42 AM.


NOTICE TO USERS OF THIS SITE: By continuing to use this site, you certify that you have read and agree to abide by the Legal Terms of Use. All information, data, text or other materials ("Content") posted to this site by any users are the sole responsibility of those users. 1911Forum does not guarantee the accuracy, integrity, or quality of such Content.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 2015 1911Forum.com, LLC. All Rights Reserved