1911Forum - Search Results
1911Forum
Advertise Here
Forum   Reviews   Rules   Legal   Site Supporters & Donations   Advertise


Go Back   1911Forum >

Notices


Showing results 1 to 16 of 16
Search took 0.02 seconds.
Search: Posts Made By: Rita
Forum: Other 1911's 11-04-2014, 06:09 PM
Replies: 41
Views: 5,158
Posted By Rita
I purchased an AO 1911 that was built after Kahr...

I purchased an AO 1911 that was built after Kahr took ownership. It has been a piece of X#%*[email protected] Several parts have broken and replacement parts don't come close to fitting. I wrote a high up...
Forum: Gunsmithing & Troubleshooting 04-09-2013, 09:15 PM
Replies: 1,094
Views: 352,665
Posted By Rita
I always use the following on my Italian made...

I always use the following on my Italian made pistols: Basil-Infused Olive Oil.
Forum: Gunsmithing & Troubleshooting 02-06-2013, 01:40 PM
Replies: 7
Views: 1,317
Posted By Rita
Snorkel Does the ejector on your Colt Series 7...

Snorkel
Does the ejector on your Colt Series 7 Commander have that L shape extension at the top? Mine is basically a rectangle without the small extension at the top.
Forum: Gunsmithing & Troubleshooting 02-06-2013, 11:44 AM
Replies: 7
Views: 1,317
Posted By Rita
Commander Ejector--are all extended?

I have been having ejection problems with my Kahr made 1911 Commander. The ejector in this gun has no extension like you see in the Brownells catalog. The face is also not cut at a 90 degree angle....
Forum: Gunsmithing & Troubleshooting 01-29-2013, 05:16 PM
Replies: 5
Views: 840
Posted By Rita
Help needed

I purchased a new Nowlin extractor and tried to install it in my series 70 model 1911. Unfortunately, the circumference of the large rear end of the extractor is greater than the circumference of...
Forum: Ammo Can 01-24-2013, 08:21 PM
Replies: 3
Views: 2,531
Posted By Rita
Able Ammo Problem

I ordered ammo from Able Ammo. When I ordered the ammo, some items were marked out of stock. (I did not order items marked out of stock.) I assumed if the items were not marked out of stock, it...
Forum: Browning Hi-Power 06-03-2009, 12:03 PM
Replies: 23
Views: 3,055
Posted By Rita
My BHP is the most accurate and dependable gun I own.

I would trust my life to it before any of my 1911's. The BHP is a Mrk II that was worked over by C&S about fifteen years ago. Freehand groups at 10 yards are so tight that most holes in the paper...
Forum: Gunsmithing & Troubleshooting 06-02-2009, 07:04 PM
Replies: 12
Views: 3,180
Posted By Rita
I had the exact same problem with Mag Tech 45 ammo and posted about it last week.

No matter what magazine I used I had ejection problems with Mag Tech in my 1911. Other brands ran fine. I wonder if there is some bad Mag Tech ammo out there?
Forum: Gunsmithing & Troubleshooting 05-27-2009, 06:04 PM
Replies: 2
Views: 673
Posted By Rita
Failure to eject.

All of a sudden my 1911 has begun to have problems ejecting spent shells. The slide closes on the ejected shell. The spent shell has not rotated yet. What would cause this to happen? It happens...
Forum: Gunsmithing & Troubleshooting 03-17-2009, 09:23 PM
Replies: 6
Views: 1,897
Posted By Rita
Forum: Les Baer 03-07-2009, 03:33 PM
Replies: 22
Views: 3,279
Posted By Rita
Has Les Baer quality changed since the move to IA? How does Clark compare?

Cant make up my mind between a Clark and a Baer.
Forum: Gunsmithing & Troubleshooting 03-07-2009, 01:23 PM
Replies: 5
Views: 1,355
Posted By Rita
Help: retaining screw on Heinie Slant-pro rear sight

I had set of Heinie sights installed by a gunsmith. The rear sight was returned without a retaining screw. While the sight seem tight, I wrote the gunsmith (who is several states away) and asked...
Forum: Gunsmithing & Troubleshooting 02-26-2009, 10:01 PM
Replies: 4
Views: 885
Posted By Rita
Slide Stop Problem

The problem I am describing only occurs with EMPTY magazines. When I use Wolff brand magazines and pull the slide back, I cannot push the slide stop down in order to release the slide and let it...
Forum: Gunsmithing & Troubleshooting 02-25-2009, 01:36 PM
Replies: 5
Views: 939
Posted By Rita
Recoil Spring

Should the recoil spring be hard to put on the recoil spring guide rod? If I put the closed end on the guide rod, I have to twist it on. Is this normal? Kahr (Auto-Ordnance) says to put the OPEN...
Forum: Gunsmithing & Troubleshooting 02-22-2009, 06:17 PM
Replies: 14
Views: 4,884
Posted By Rita
Forum: Gunsmithing & Troubleshooting 02-22-2009, 06:06 PM
Replies: 8
Views: 1,148
Posted By Rita
Don Williams (actionworks.com) installed my front and rear sights.

I have always found his work first rate and his prices to be very fair. A good person to deal with to. You will only need to send him the slide so you can use ground transport as well as the USPS.
Showing results 1 to 16 of 16

 
Forum Jump

All times are GMT -5. The time now is 06:43 AM.


NOTICE TO USERS OF THIS SITE: By continuing to use this site, you certify that you have read and agree to abide by the Legal Terms of Use. All information, data, text or other materials ("Content") posted to this site by any users are the sole responsibility of those users. 1911Forum does not guarantee the accuracy, integrity, or quality of such Content.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2015 1911Forum.com, LLC. All Rights Reserved