1911Forum - Search Results
1911Forum
Advertise Here
Forum   Reviews   Rules   Legal   Site Supporters & Donations   Advertise


Go Back   1911Forum >

Notices


Showing results 1 to 25 of 2000
Search took 4.89 seconds.
Search: Posts Made By: cdhbrad
Forum: Reloading Bench 03-19-2020, 02:08 PM
Replies: 7
Views: 483
Posted By cdhbrad
Coated, No Lube Groove, cast lead is pretty much...

Coated, No Lube Groove, cast lead is pretty much all I shoot. All seem to work as well or better than Coated with a Lube Groove.
Forum: Disaster Preparedness 03-19-2020, 02:05 PM
Replies: 14
Views: 1,120
Posted By cdhbrad
"The sheriff of the next county over just posted...

"The sheriff of the next county over just posted a warning about folks...." Which direction from Highlands?? I'm in Manatee so two counties over if to the West. Be safe out there.
Forum: Reloading Bench 03-18-2020, 08:18 PM
Replies: 28
Views: 852
Posted By cdhbrad
Iím OK. Have about 60K primers, 50# of powder...

Iím OK. Have about 60K primers, 50# of powder and at least 10K bullets on hand. Bullets are easiest to replace. Probably 15K loaded rounds on the shelves. At least 20K empty brass.
Pays to...
Forum: Reloading Bench 03-17-2020, 06:11 AM
Replies: 13
Views: 437
Posted By cdhbrad
I have used Blue Bullets 9mm and they work fine. ...

I have used Blue Bullets 9mm and they work fine. I mainly shoot TC vs. RN. I like the versions from SNS Casting and Missouri Bullet Co.
Forum: Dan Wesson 03-07-2020, 05:39 AM
Replies: 38
Views: 1,246
Posted By cdhbrad
When I need extra magazines for my 1911s,...

When I need extra magazines for my 1911s, including my 5 DWs, I go with Tripp. Work fine in .45 ACP, .40 S&W, and 9mm. I get them through Harrison Design.
Forum: Parts and Accessories Bin 03-06-2020, 03:40 PM
Replies: 1
Views: 206
Posted By cdhbrad
Pretty good odds that Kensight made the...

Pretty good odds that Kensight made the adjustable sight that is on your Springfield right now: https://stores.kensight.com/springfield-armory/ They show an adjustable night sight. I have several...
Forum: General Gun Discussion 03-04-2020, 06:57 PM
Replies: 76
Views: 2,921
Posted By cdhbrad
Me too....My first was a Series 80 Gold Cup...

Me too....My first was a Series 80 Gold Cup bought in early 90s, still have it. My only other Colt is a Clark Hardball built in 1962 on a late 50s Govt. Model. Rob Schauland (ACW) recently...
Forum: Dan Wesson 03-03-2020, 07:19 PM
Replies: 11
Views: 736
Posted By cdhbrad
If you need CZ parts, go to Cajun Gun Works or CZ...

If you need CZ parts, go to Cajun Gun Works or CZ Custom.
Forum: Dan Wesson 02-28-2020, 02:00 PM
Replies: 11
Views: 736
Posted By cdhbrad
Glad you heard back from DW. I would have just...

Glad you heard back from DW. I would have just gone to Harrison Design, my go to for anything 1911, and ordered this: https://shop.harrisoncustom.com/hd-211-firing-pin-389mm and a firing pin...
Forum: Gunsmithing & Troubleshooting 02-25-2020, 05:34 AM
Replies: 33
Views: 1,440
Posted By cdhbrad
White G10 if you just want to admire the gun,...

White G10 if you just want to admire the gun, which I do, and Black G10 if you are going to shoot it. Ask me how I know?👍😀👍
Forum: Dan Wesson 02-21-2020, 05:44 AM
Replies: 9
Views: 424
Posted By cdhbrad
I have the Harrison slide stop on several custom...

I have the Harrison slide stop on several custom 1911s and prefer them on builds of that type where I choose all the parts.....I'm also partial to Harrison thumb safeties. I also have 4 DW Valors...
Forum: Dan Wesson 02-20-2020, 02:42 PM
Replies: 110
Views: 11,772
Posted By cdhbrad
The SAO trigger on a TSO is significantly...

The SAO trigger on a TSO is significantly different than those on other CZ, including the new AO1-ld. Mine is excellent and, I'd agree with TRS Otto, better than almost any 1911 I have except,...
Forum: Dan Wesson 02-13-2020, 10:56 AM
Replies: 27
Views: 1,668
Posted By cdhbrad
That was good enough for me when I bought a SS...

That was good enough for me when I bought a SS Valor 9mm from them last year. Perfect transaction in every way.
Other folks just need to hear it from unknown folks on an Internet gun forum. ...
Forum: Dan Wesson 02-10-2020, 05:56 AM
Replies: 9
Views: 657
Posted By cdhbrad
I agree with you, they work fine. Could also be...

I agree with you, they work fine. Could also be that DW sources spring plugs from EGW and they only make two lengths: Commander and 6Ē slide.
Forum: Reloading Bench 02-04-2020, 09:13 AM
Replies: 47
Views: 3,928
Posted By cdhbrad
If the OP has any N310, 4.0 gr. with a 185 LSWC...

If the OP has any N310, 4.0 gr. with a 185 LSWC works well for me too. I've found that 4.0 gr of either Bullseye or N310 are easy to shoot and very accurate in all my full sized 1911s.

All mine...
Forum: Reloading Bench 01-28-2020, 06:03 AM
Replies: 12
Views: 1,331
Posted By cdhbrad
I have only used Sport Pistol in 9mm and load the...

I have only used Sport Pistol in 9mm and load the same charge as with N320. For a 125gr Coated bullet, 4.0gr works in all my 1911s using a 12# Recoil Spring and my CZs with similar weight springs. ...
Forum: Dan Wesson 01-24-2020, 02:17 PM
Replies: 8
Views: 794
Posted By cdhbrad
I've bought 4 of my DWs from Sellers' on GB. The...

I've bought 4 of my DWs from Sellers' on GB. The fifth was a Custom direct from DW. I've not been disappointed with any of the DW transactions.
Forum: Dan Wesson 01-05-2020, 07:32 AM
Replies: 5
Views: 490
Posted By cdhbrad
That would work too, but would still require some...

That would work too, but would still require some millwork on the slide.
Forum: Dan Wesson 01-04-2020, 06:42 PM
Replies: 5
Views: 490
Posted By cdhbrad
What you describe is possible, but expensive to...

What you describe is possible, but expensive to do. Much easier to use an adjustable sight that fits the existing Novak/Lo-Mount cut. I have two Valors with the Dawson adjustable rear sight. Work...
Forum: Reloading Bench 12-17-2019, 05:25 AM
Replies: 46
Views: 2,701
Posted By cdhbrad
SNS Casting and Missouri Bullet Co are my go to...

SNS Casting and Missouri Bullet Co are my go to sources for coated cast bullets. Between them, they have the weights and shapes I want to load for 9mm, 40 S&W, and 45 ACP.
For .45, 200gr SWC are...
Forum: Reloading Bench 12-09-2019, 01:51 PM
Replies: 30
Views: 1,857
Posted By cdhbrad
RCBS Bench tool is what I use for rifle brass. I...

RCBS Bench tool is what I use for rifle brass. I have the Inline Fab quick change plates on my bench and they make a plate to fit the RCBS Bench tool.
Forum: Parts and Accessories Bin 12-06-2019, 10:21 AM
Replies: 15
Views: 1,230
Posted By cdhbrad
I don't know of any functional purpose top slide...

I don't know of any functional purpose top slide serrations serve. You can't see them when shooting the pistol. That said, I do like them and have had them done on some of my 1911
Forum: Dan Wesson 11-26-2019, 09:14 AM
Replies: 4
Views: 723
Posted By cdhbrad
I'm with you. I have a couple of SS Valors and...

I'm with you. I have a couple of SS Valors and on my last one, a 9mm, I put 50 rounds of remanufactured ammo from Freedom through it before switching to my handloads. I think I field stripped it...
Forum: General Gun Discussion 11-26-2019, 05:22 AM
Replies: 16
Views: 1,014
Posted By cdhbrad
I have a CZ97B that I sometimes carry in a...

I have a CZ97B that I sometimes carry in a holster at a range. I had a Tucker HF-1 made for mine. Very sturdy holster for a big pistol. They made a Mag pouch too.
Forum: Dan Wesson 11-24-2019, 07:46 PM
Replies: 5
Views: 648
Posted By cdhbrad
Several listed now on Gunbroker in .45 and 9mm...

Several listed now on Gunbroker in .45 and 9mm with multiple actual photos. Probably best you can do for pics.
Showing results 1 to 25 of 2000

 
Forum Jump

All times are GMT -5. The time now is 01:30 AM.


NOTICE TO USERS OF THIS SITE: By continuing to use this site, you certify that you have read and agree to abide by the Legal Terms of Use. All information, data, text or other materials ("Content") posted to this site by any users are the sole responsibility of those users. 1911Forum does not guarantee the accuracy, integrity, or quality of such Content.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2015 1911Forum.com, LLC. All Rights Reserved