1911Forum - Search Results
1911Forum
Advertise Here
Forum   Reviews   Rules   Legal   Site Supporters & Donations   Advertise


Go Back   1911Forum >

Notices


Showing results 1 to 10 of 10
Search took 0.14 seconds.
Search: Posts Made By: NotHankHill
Forum: Gunsmithing & Troubleshooting 03-03-2020, 08:23 AM
Replies: 17
Views: 1,242
Posted By NotHankHill
Sorry for the double post. Obviously I'm forum...

Sorry for the double post. Obviously I'm forum illiterate because I couldn't figure out how to edit my old post. I haven't been able to do anything with this lately as my arthritis in my left hand...
Forum: Gunsmithing & Troubleshooting 02-25-2020, 06:52 AM
Replies: 17
Views: 1,242
Posted By NotHankHill
Did this on the old one to test. Still catching....

Did this on the old one to test. Still catching. When I can this week I'm going to take the fcg out along with all the rear stuff and give everything a once over again with a fine stone. I'll update...
Forum: Gunsmithing & Troubleshooting 02-22-2020, 07:27 PM
Replies: 17
Views: 1,242
Posted By NotHankHill
It was the Stealth Arms 80% Build kit. All parts...

It was the Stealth Arms 80% Build kit. All parts are Series 70 1911 parts. I will look for milling issues, but otherwise everything seems to fit and move properly. The grip safety itself isn't...
Forum: Gunsmithing & Troubleshooting 02-22-2020, 03:09 PM
Replies: 17
Views: 1,242
Posted By NotHankHill
So after finishing the rest of what I needed to...

So after finishing the rest of what I needed to do (lapping mostly) I've come back to this. New GS does the same thing the old did before too much removed material. I covered it in sharpie as well...
Forum: Gunsmithing & Troubleshooting 02-16-2020, 11:52 PM
Replies: 17
Views: 1,242
Posted By NotHankHill
Where did you file - the forward end or the...

Where did you file - the forward end or the underside (horizontal surface) in the notch? A light shown up through the mag well should make it visible.[/QUOTE]

The underside of the very end, in the...
Forum: Gunsmithing & Troubleshooting 02-16-2020, 10:38 PM
Replies: 17
Views: 1,242
Posted By NotHankHill
Well I shaved a bit more off, one file at a time...

Well I shaved a bit more off, one file at a time then test. Still both hang ups. Last time testing and the hammer falls, but without the GS being depressed. The trigger still hangs up and hammer...
Forum: Gunsmithing & Troubleshooting 02-15-2020, 04:07 PM
Replies: 17
Views: 1,242
Posted By NotHankHill
Yep, typical result of the safety arm being a...

Yep, typical result of the safety arm being a little too long.

Use a felt tip marker and see where it's touching, then remove some metal. Use a very fine file or sandpaper glued to a stick to...
Forum: Gunsmithing & Troubleshooting 02-15-2020, 08:37 AM
Replies: 17
Views: 1,242
Posted By NotHankHill
Any suggested pictures I should post? I have to...

Any suggested pictures I should post? I have to physically pull the trigger forward to reset it and the GS pops out then. The trigger and GS are definitely binding, I'm just not sure if that's what's...
Forum: Gunsmithing & Troubleshooting 02-14-2020, 10:03 PM
Replies: 17
Views: 1,242
Posted By NotHankHill
Okay. I already did that once. I was thinking...

Okay. I already did that once. I was thinking that I needed to take more off from what I gathered, but wanted to make sure before I removed too much. I also noticed that the trigger isn't resetting...
Forum: Gunsmithing & Troubleshooting 02-14-2020, 05:56 PM
Replies: 17
Views: 1,242
Posted By NotHankHill
StealthArms 80% Safety Issue

So I had this beast all "complete" last night with the exception of fine stuff. Just a rough fit, slide was tight, etc.

Today I decide in prep for the fine detail work, I would take it apart and...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -5. The time now is 03:30 PM.


NOTICE TO USERS OF THIS SITE: By continuing to use this site, you certify that you have read and agree to abide by the Legal Terms of Use. All information, data, text or other materials ("Content") posted to this site by any users are the sole responsibility of those users. 1911Forum does not guarantee the accuracy, integrity, or quality of such Content.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2015 1911Forum.com, LLC. All Rights Reserved