1911Forum - Search Results
1911Forum
Advertise Here
Forum   Reviews   Rules   Legal   Site Supporters & Donations   Advertise


Go Back   1911Forum >

Notices


Showing results 1 to 12 of 12
Search took 0.00 seconds.
Search: Posts Made By: Pony doc
Forum: Gunsmithing & Troubleshooting 03-02-2020, 07:04 PM
Replies: 37
Views: 2,736
Posted By Pony doc
Ok. Finally had time to measure. This is from the...

Ok. Finally had time to measure. This is from the back edge of the magazine to the beginning of the release point. Nothing really stands out to me looking at the measurements. Mag 13 is the least...
Forum: Gunsmithing & Troubleshooting 02-25-2020, 06:15 PM
Replies: 37
Views: 2,736
Posted By Pony doc
Ok. At long last I have measurements of the I.d....

Ok. At long last I have measurements of the I.d. width of the feedlips at the release point. The star indicates the troublesome mag. Dots indicates mags that have demonstrated the missfeed...
Forum: Gunsmithing & Troubleshooting 02-23-2020, 11:47 AM
Replies: 37
Views: 2,736
Posted By Pony doc
Disassembled both pistols and taped the barrels...

Disassembled both pistols and taped the barrels in place. Used my thumb to push several mags worth of cartridges from both the troublesome mag and one that has never malfunctioned through each...
Forum: Gunsmithing & Troubleshooting 02-22-2020, 06:48 PM
Replies: 37
Views: 2,736
Posted By Pony doc
Measurements ware made at the back of the...

Measurements ware made at the back of the feedlips o.d. measurement. Maybe that is not right?
Forum: Gunsmithing & Troubleshooting 02-22-2020, 05:34 PM
Replies: 37
Views: 2,736
Posted By Pony doc
Been busy investigating. Measured the feedlips on...

Been busy investigating. Measured the feedlips on 13 mags. Measurements are in the photo attached. The star next to mag 13 means it has been my most troublesome mag. The two with dots indicate that...
Forum: Gunsmithing & Troubleshooting 02-19-2020, 08:27 PM
Replies: 37
Views: 2,736
Posted By Pony doc
I tried measuring feed lips but it was pretty...

I tried measuring feed lips but it was pretty much a bust. It was difficult to measure the back of the feedlip with enough consistency to make meaningful comparisons. It was difficult to keep the...
Forum: Gunsmithing & Troubleshooting 02-18-2020, 06:54 PM
Replies: 37
Views: 2,736
Posted By Pony doc
Yes I shoot 230 round nose lead bullets from...

Yes I shoot 230 round nose lead bullets from Missouri Bullet Co. Best I can tell they are the same profile as hardball. Most of my brass lands 2-4 feet away. I am shooting a fairly moderate load of...
Forum: Gunsmithing & Troubleshooting 02-17-2020, 08:51 PM
Replies: 37
Views: 2,736
Posted By Pony doc
1911 Tuner is the reason I am using the Checkmate...

1911 Tuner is the reason I am using the Checkmate hybrid feed lip magazines. I will get a micrometer and measure my magazines this weekend. I have kept records for the last year on which magazines...
Forum: Gunsmithing & Troubleshooting 02-16-2020, 07:34 PM
Replies: 37
Views: 2,736
Posted By Pony doc
How do I do this. I am using a Wilson bulletproof...

How do I do this. I am using a Wilson bulletproof extractor ( which did decrease the incidence of this type of misdeed) and Wilson said just install as is.
Forum: Gunsmithing & Troubleshooting 02-16-2020, 06:35 PM
Replies: 37
Views: 2,736
Posted By Pony doc
Is the GI taper preferred if someone is only...

Is the GI taper preferred if someone is only going to shoot RNL shaped bullets?
Forum: Gunsmithing & Troubleshooting 02-16-2020, 06:25 PM
Replies: 37
Views: 2,736
Posted By Pony doc
It is factory 16 lb recoil spring. 23 lb...

It is factory 16 lb recoil spring. 23 lb mainspring. All of my Colt and Checkmate mags have had the springs replaced with Wolf extra power springs. The new Ed Brown mags made by Checkmate have really...
Forum: Gunsmithing & Troubleshooting 02-16-2020, 05:02 PM
Replies: 37
Views: 2,736
Posted By Pony doc
What is the cause of this missfeed?

I continue to have this missfeed about once every hundred rounds. A live round partially feeds into the chamber and the round is not under control of the extractor. I had this malfunction more...
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT -5. The time now is 08:36 PM.


NOTICE TO USERS OF THIS SITE: By continuing to use this site, you certify that you have read and agree to abide by the Legal Terms of Use. All information, data, text or other materials ("Content") posted to this site by any users are the sole responsibility of those users. 1911Forum does not guarantee the accuracy, integrity, or quality of such Content.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2015 1911Forum.com, LLC. All Rights Reserved