1911Forum
Forum   Reviews   Rules   Legal   Site Supporters & Donations   Advertise


Go Back   1911Forum > Hardware & Accessories > Parts and Accessories Bin


Reply
 
Thread Tools Display Modes
  #1  
Old 11-30-2012, 02:10 PM
mchj74 mchj74 is offline
Member
 
Join Date: Mar 2012
Posts: 55
Egw barrel bushing




Just wanted to get some in put on the EGW angle bore barrel bushing. I am thinking about getting an EGW Carry Bevel Bushing. I am want to know if it is worth it to get the angle bore or just go with the stright bore. The gun I am getting it for is a Springfield loaded px9151lp
Reply With Quote
  #2  
Old 11-30-2012, 03:52 PM
Brian R. Brian R. is offline
Member
 
Join Date: Nov 2011
Location: Rockville, MD
Posts: 844
I bought and fit the angled bore and have had no trouble with it. Very good product.
__________________
"What we got here is a failure to communicate."
Reply With Quote
  #3  
Old 11-30-2012, 04:14 PM
rebo0t rebo0t is offline
Member
 
Join Date: Aug 2012
Posts: 134
I have a custom angle bore and love it
Reply With Quote
  #4  
Old 11-30-2012, 04:21 PM
dakotaTex dakotaTex is offline
Member
 
Join Date: Jul 2009
Location: Texas
Posts: 1,199
I bought a S70 Gold Cup that had a mis-matched barrel bushing. It was the collet type, but clearly for a different barrel. I ordered an EGW angled bushing and the gun now shoots extremely well. Went from a lemon to sweet lemonade. I have another S70 that's a bit of a FrankenColt that I may do the same thing with.

However, you do need accurate measurements to make it worthwhile. I used an inexpensive Frankford Arsenal electronic caliper I bought on sale at MidwayUSA quite a while ago and took about 10 measurements and averaged them out. I also spoke with EGW on the phone to make sure I was on the right track. They were very helpful.

Good luck,


dakotaTex
Reply With Quote
  #5  
Old 11-30-2012, 06:53 PM
staysafe staysafe is offline
Member
 
Join Date: Sep 2010
Posts: 872
+1 on angle
Reply With Quote
  #6  
Old 11-30-2012, 11:14 PM
rjinaz85308 rjinaz85308 is online now
Member
 
Join Date: May 2011
Location: Phoenix,AZ
Posts: 1,262
Very nice and minimal fitting

__________________
Only two defining forces have ever offered to die for you,
Jesus Christ and the American GI.
One died for your soul; the other for your freedom..

We should be thankful to both
Reply With Quote
  #7  
Old 12-01-2012, 01:34 AM
Trikegodtroll Trikegodtroll is offline
Member
 
Join Date: Jul 2010
Location: Eastern Oregon
Age: 52
Posts: 493
I went with the "angle bore bushing" too. Didnt want the chance of the barrel springing.
Good luck on yours.......................................... Troy


Reply With Quote
  #8  
Old 12-01-2012, 01:53 AM
Earlsbud Earlsbud is offline
Senior Member
 
Join Date: Apr 2011
Location: Home of the brave.
Posts: 2,099
Get the thick flange. Supply your measurements and fit it. It is worth the effort. Slide your calipers from the barrel end back about 3/4 of an inch and give the largest bbl. OD read when you order. It will vary/change as you move the calipers. A dowel rod cut to 6" lengths and sand paper from the auto parts store, 230-2000 grit .........and you will shrink your groups. Well worth the effort.
__________________
Proud NRA Life Member.
Reply With Quote
  #9  
Old 12-01-2012, 10:36 AM
rex rex is offline
Senior Member
 
Join Date: Jan 2001
Location: S. FL
Posts: 3,129
Good bushing.Take many measurements,as in 12-6,3-9,1:30-7:30 on the clock.The slide limits it but find the tightest and give them that measurement.They correct for the barrel clearance,the OD may need a liitle messaging to get in the slide at worst.
Reply With Quote
  #10  
Old 12-01-2012, 11:13 PM
mchj74 mchj74 is offline
Member
 
Join Date: Mar 2012
Posts: 55
Thanks guys got it ordered
Reply With Quote
  #11  
Old 12-03-2012, 01:45 AM
triggerbear triggerbear is offline
Junior Member
 
Join Date: Jun 2008
Location: alabama
Age: 51
Posts: 7
I had to take a bit off the flange to clear the wilson gr plug. much tighter groups with my springer now.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:58 AM.


NOTICE TO USERS OF THIS SITE: By continuing to use this site, you certify that you have read and agree to abide by the Legal Terms of Use. All information, data, text or other materials ("Content") posted to this site by any users are the sole responsibility of those users. 1911Forum does not guarantee the accuracy, integrity, or quality of such Content.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 2011 1911Forum.com, LLC. All Rights Reserved