1911Forum
Forum   Reviews   Rules   Legal   Site Supporters & Donations   Advertise


Go Back   1911Forum > 1911 Manufacturers > Sig Sauer
Reload this Page HELP: Possible slide issue?
Register FAQ Gun Safety Search Today's Posts Mark Forums Read


Reply
Page 2 of 2 1 2
 
Thread Tools Display Modes
  #26  
Old 07-11-2012, 03:25 PM
SmurfHunter SmurfHunter is offline
Member
  
Join Date: Jan 2012
Posts: 1,111
Quote:
Originally Posted by LEO2B View Post
OK, cool, just wanted to let you know. Now that it's dry use a tooth brush to clean out the rail slots in the frame and slide, use a light coating of mil spec grease in there.

In your picture it looks like your slide stop wear area, against the frame, is a little excessive for just a 250 rd. gun. Can you post a pict. of the slide stop out of the pistol?
That's what I was saying earlier. That slide stop looked to be on wayyyyyy to tight.
Reply With Quote
  #27  
Old 07-12-2012, 09:57 AM
Bdubbs24 Bdubbs24 is offline
Member
  
Join Date: Jul 2012
Location: MN
Posts: 151
Well sig sent me an overnight shipping stamp, and they already have it, so we'll see what they say.
Reply With Quote
  #28  
Old 07-12-2012, 10:00 PM
Onegoodshot Onegoodshot is offline
Senior Member
  
Join Date: Jul 2008
Location: between way back when and until then
Posts: 4,021
Keep finger off the trigger during re assembly. Engaging firing pin safety will result.
Kimber II owners have to keep off the grip safety for same reason.
Reply With Quote
  #29  
Old 07-13-2012, 07:52 PM
Bdubbs24 Bdubbs24 is offline
Member
  
Join Date: Jul 2012
Location: MN
Posts: 151
Quote:
Originally Posted by Onegoodshot View Post
Keep finger off the trigger during re assembly. Engaging firing pin safety will result.
Kimber II owners have to keep off the grip safety for same reason.
I do, I've never put my finger on the trigger when putting it back together.
Reply With Quote
  #30  
Old 07-13-2012, 08:20 PM
chaingunner chaingunner is offline
Member
  
Join Date: Aug 2005
Location: upstate N.Y.
Age: 56
Posts: 81
Looked like the thumb safety had some wear from the slide, could the safety have been partially engaged? Just a thought...
__________________
The best weapon for self defense is kept between your ears.
Reply With Quote
  #31  
Old 07-14-2012, 06:12 AM
scottybaccus scottybaccus is offline
Junior Member
  
Join Date: Jul 2012
Posts: 17
On the Sig external extractors, the bore for the pivot pin extends down into the slide rails. If this pin were to move down into the rails, it would bind up the slide.

I was trying to spot wear marks on your frame rail in this area.
Reply With Quote
  #32  
Old 07-16-2012, 09:02 AM
Bdubbs24 Bdubbs24 is offline
Member
  
Join Date: Jul 2012
Location: MN
Posts: 151
Well I already have a tracking number and I should have my pistol back by tomorrow. I never got a call from sig on what the issue was. I can say this though, so far there customer service is top notch and there turn around is fast.
Reply With Quote
  #33  
Old 07-17-2012, 12:52 PM
Bdubbs24 Bdubbs24 is offline
Member
  
Join Date: Jul 2012
Location: MN
Posts: 151
Got my pistol back. I guess they had to adjust the ejector pin. Is this a normal problem or not? I'll hopefully get some shooting done this weekend.
Reply With Quote
  #34  
Old 07-18-2012, 09:37 PM
custom2's Avatar
custom2 custom2 is offline
Moderator
  
Join Date: Jan 2009
Posts: 4,374
The ejector pin can protrude from the frame if it isn't installed all the way in but I have never seen one back out from shooting. Are you sure they said ejector pin and not extractor pin?
Reply With Quote
  #35  
Old 07-20-2012, 10:26 AM
Bdubbs24 Bdubbs24 is offline
Member
  
Join Date: Jul 2012
Location: MN
Posts: 151
Quote:
Originally Posted by custom2 View Post
The ejector pin can protrude from the frame if it isn't installed all the way in but I have never seen one back out from shooting. Are you sure they said ejector pin and not extractor pin?
The slip they sent back with the gun say's, inspected the pistol, and adjusted the ejector pin. So maybe it wasn't exactly right from the get go? Hope this wont be a re-ocurring issue.
Reply With Quote
  #36  
Old 07-20-2012, 10:36 AM
custom2's Avatar
custom2 custom2 is offline
Moderator
  
Join Date: Jan 2009
Posts: 4,374
It may have been out from the get go. It should GTG now.
Reply With Quote
  #37  
Old 07-20-2012, 01:50 PM
Bdubbs24 Bdubbs24 is offline
Member
  
Join Date: Jul 2012
Location: MN
Posts: 151
Quote:
Originally Posted by custom2 View Post
It may have been out from the get go. It should GTG now.
Hope so! May get some shooting done today or this weekend.
Reply With Quote
  #38  
Old 07-20-2012, 07:27 PM
Bdubbs24 Bdubbs24 is offline
Member
  
Join Date: Jul 2012
Location: MN
Posts: 151
Well I went out shooting today! Only shot about 130rds, but had zero problems!
Reply With Quote
  #39  
Old 07-20-2012, 10:11 PM
custom2's Avatar
custom2 custom2 is offline
Moderator
  
Join Date: Jan 2009
Posts: 4,374
Good to hear it.
Reply With Quote
Reply
Page 2 of 2 1 2

Bookmarks

« Previous Thread | Next Thread »
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 05:44 PM.

Advertising Info - Contact Us - 1911Forum - Privacy Statement - Terms of Service - Top

NOTICE TO USERS OF THIS SITE: By continuing to use this site, you certify that you have read and agree to abide by the Legal Terms of Use. All information, data, text or other materials ("Content") posted to this site by any users are the sole responsibility of those users. 1911Forum does not guarantee the accuracy, integrity, or quality of such Content.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, vBulletin Solutions, Inc.
Copyright 2011 1911Forum.com, LLC. All Rights Reserved